Barrel and Auxiliary Shaft Assembly

Housing Assembly Install

04-24-2006 05;12;55AM

1. Fit in the barrel (1) with the bores facing down on a clean area.

  • Place the hold down spring (3) into barrel counter- bore.
  • Put in spring retainer (5) into counter bore and seat next to spring.
  • Place the retaining ring (6) into barrel counter- bore groove. Align retaining ring so that it is fully seated in groove.
  • Fix the barrel stop (4) over auxiliary drive shaft (2). Rotate barrel on side and put the auxiliary drive shaft and barrel stop into the barrel spline and hold down spring.

    basicTable.html

    Parts List

    No. Qty. Part Number Explanation
    1 1 513-45381 Barrel & sleeve assy only
    1 1 S13-43965 Barrel & sleeve assy only
    2 1 033-71603 Auxiliary drive shaft
    3 1 033-71562 Holddown spring
    4 1 033-71561 Barrel stop
    5 1 033-71560 Spring retainer
    6 1 033-71564 Retaining ring

    Guidelines for Replenishing Circuit Isolation Plug


    WARNING

    The isolation plug together with this is to be used only if an external filter circuit is not offered DO NOT operate this unit with the isolation plug put in unless an outside line has been provided.

    When the outer filter circuit is not used, dispose of the isolation plug. When the outside filter circuit is used, fit the isolation plug under the plug in the face of the port block. Use a 3/16" hex wrench, 4" minimum in length. Insert the isolation plug and tighten to 80-120 in./lbs. torque. Warning Filter should have a bypass and bypass indicator and Hydrostatic Transmission Service, LLC which offers Denison recommends that it be sized four times for projected flow.

    HOUSING ASSEMBLY S13-43962

  • 1. Place housing (1) on a flat area with the large open end up.
  • 2. Push the bearing (2) into the housing bore until seated. IT IS NOT RECOMMENDED THAT HAMMERING OR BEATING THE BEARING INTO PLACE.
  • 3. Put housing on side and install roll pin (3) into the hole in control cover pad. Roll pin ought to be installed 3/8" under pad surface. Place two dowel pins (4) in the blind holes in the same pad.
  • 4. DO this (step 3) on the opposite side of the housing.
  • 5. Fit together O-ring (5) and plug (6) in the bottom of housing. Roll pins (3) are in the bottom half of the housing.
  • basicTable.html

    Housing Assembly S13-43962 Parts List

    No. Qty. Part Number Description
    1 1 033-71578 Housing
    2 1 033-71516 Bearing
    3 2 325-16320 Roll pin
    4 4 324-21608 Dowel gin
    5 1 691-00912 0-rmg
    6 1 488-35014 Plug

    Caution: Be sure the Loose Pin is retained in the Port when putting together the System Pressure Gage.

    USUAL PRESSURES

  • Servo—160 psi -(-case psi -(-62.5 psi per 1000 system pressure.
  • Replenishment—180-220 psi + Case Pressure.
  • Servo—300 psi + case
  • psi +40 psi per 1000 system pressure.
  • Case—75 psi continuous 125 psi intermittent


  • Housing Assembly Install

    04-24-2006 05;12;55AM
    Housing Assembly Install

    04-24-2006 05;12;55AM
    Housing Assembly Install

    04-24-2006 05;12;55AM

    For a list of our Eaton pumps and prices, go to our Eaton hydrostatic parts page

    Or visit us at our EBay store: Hydrostatic Transmission Service, LLC

    HYDRAULIC REPAIR – HYDROSTATIC PUMPS – HYDROSTATIC EQUIPMENT

    CALL US FOR YOUR REPAIR ON DIFFICULT TO LOCATE HYDROSTATIC TRANSMISSION REPAIR.

    MITSUBISHI, KAWASAKI, DAEWOO, DYNAPOWER, LINDE, REXROTH, UCHIDA, YAMAHA, HITACHI, KOMATSU, LIEBHERR, POCLAIN, VOLVO, VICKERS, CESSNA, HYDROMATIK, SUNDSTRAND AND EATON CLOSED LOOP AND OPEN LOOP HYDROSTATIC DRIVE PUMPS AND MOTORS.

    404 Air Park Rd
    Tupelo, MS 38801
    Phone: (662) 680-8899
    Toll Free: (800) 361-0068

    Email: sales@htsrepair.com

    PayPal service to make fast, easy, and secure payments for your Internet purchases!

    PayPal for Easy PaymentsBank Transfer Options

    We accept major Credit Cards

    Disclaimer: All references to OEM words are strictly for reference only and does not imply that we are an OEM distributor.

    [Home] [Sundstrand Pump Repair] [Eaton Pump Repair] [Hydrostatic] [Parts Exchange] [Hydrostatic Parts] [Hydrostatic Pumps] [Hydrostatic Repair] [Excavator Pumps] [Equipment Pumps] [John Deere Pump Repair] [Oil Gear Pumps] [Rexroth Pumps] [Sundstrand Repair] [Vickers Pumps] [Buying Pumps] [Denison Pumps] [Hydrostatic Articles] [Railroad] [Snow Equipment] [Agricultural] [Hydraulic Repair] [Lawn Tractor] [Aquaculture Hydrostatic] [Hydrostatic Tractor Repair] [Material Handling] [Hydrostatic Spraying] [Harvesting Equipment] [Chippers,Grinders,Spreaders] [Hydrostatic Spraying Equipment] [Sawmill Hydrostatic] [Industrial Hydrostatic] [Agricultural Hydrostatic Pump] [Hydraulic Repair Parts] [Hydraulic, hydrostatic, robotic, pnuematic, electrical servo, valve, smc, cylinder repair and parts sales wordlwide] [John Deere Lawn Tractor/Lawn Mower/Garden] [Hydrostatic Transmission Service, LLC offers Sundstrand ,Eaton Dynapower] [Hydrostatic Transmission Service, LLC is your one stop pump repair store.] [90 series Sundstrand Hydrostatic] [John Deere Hydraulic Hydrostatic Pumps, Motors, Transmissions Drives] [Sundstrand Hydrostatic Parts and Sundstrand Repair] [Series 40 - Sundstrand Sauer Hydrostatic Transmission] [Series 40 Sundstrand Hydrostatic Parts] [Denison Hydrostatic Parts and Repair] [Denison Problem Solving] [Denison Hydrostatic Repair] [Sundstrand Hydrostatic Parts and Repair] [Sundstrand Hydrostatic Parts and Repair] [Vickers Hydrostatic Repair] [Caterpillar Pumps & Parts] [Warranty] [Links] [Contact Us]